From: James Kaufman <jkaufman**At_Symbol_Here**LABSAFETYINSTITUTE.ORG>
Subject: Re: [DCHAS-L] Pressurization of 5 gallon glass carboy
Date: Fri, 25 Feb 2022 11:56:47 -0500
Reply-To: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**Princeton.EDU>
Message-ID: CAHk9oERjbgiU2Qtxtq9VfDxQG_YzVWacw16WR7GwTXuwDZeJ8Q**At_Symbol_Here**mail.gmail.com
In-Reply-To <008c01d82a60$4b9b8520$e2d28f60$**At_Symbol_Here**verizon.net>


In addition to using strong shields, Dow also required that all glassware that was pressurized or evacuated be wrapped with appropriate tape, mesh netting, or plasti-coated.

PS. LSI now has virtual lab inspections, safety program evaluations, document reviews, plus courses and seminars ... all virtual

James A. Kaufman, PhD

Founder/President Emeritus


The Laboratory Safety Institute (LSI)

A Nonprofit Educational Organization for Safety in Science, Industry, and Education

192 Worcester Street, Natick, MA 01760-2252

(O) 508-647-1900 (F) 508-647-0062 (C) 508-574-6264 Skype: labsafe; 508-401-7406

jim**At_Symbol_Here**labsafety.org www.labsafety.org Teach, Learn, and Practice Science Safely






On Fri, Feb 25, 2022 at 10:58 AM Richard Palluzi <000006c59248530b-dmarc-request**At_Symbol_Here**lists.princeton.edu> wrote:

To be safe, the carboy would have to be behind a shield strong enough to withstand the breaking force of the expelled glass pieces and sited so as to intercept all potential paths the fragments could take. Not sure if one could possibly a metal trash can for that purpose because it lacks a top and a way to secure it easily to something strong enough. I guess you could make something but an acrylic shield would probably be faster, easier and cheaper. Casting it in Acrylic would, I suspect be much more expensive.

And shielding will protect personnel but it would still be open to criticism if the vendor does not rate the carboy for the maximum possible pressure used.

SO going back to the vendor makes sense to confirm that rating.

Richard Palluzi

BE(ChE), ME(ChE), PE, CSP,FAIChE

Pilot plant and laboratory consulting, safety, design, reviews, and training

www.linkedin.com/in/richardppalluzillc/

Richard P Palluzi LLC

72 Summit Drive

Basking Ridge, NJ 07920

rpalluzi**At_Symbol_Here**verizon.net

908-285-3782

From: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**Princeton.EDU> On Behalf Of Benjamin Ruekberg
Sent: Friday, February 25, 2022 10:07 AM
To: DCHAS-L**At_Symbol_Here**Princeton.EDU
Subject: Re: [DCHAS-L] Pressurization of 5 gallon glass carboy

I have some questions which may be relevant. (FYI, I seem to recall glass vessels for vacuum that were generously wrapped in electrical tape. Poor man's safety glass, I guess.)

Will the carboys in question conveniently fit in a metal trash can, 5 gallon solvent can, or waste basket? If so, with a suitable cover, would that not make the use of the carboys sufficiently safe? If non-metal versions of these containers are available, with room to fill the space between the carboy and the container wall with water (and means to hold the carboy down), could that be considered safe?

If the cost is not excessive, could the carboys be cast in acrylic to reinforce the glass? Screw eyes could be inserted in the plastic to secure the stopper, possibly with springs to prevent over-pressurization.

In essence, I guess, what I am asking is whether the carboys might be rendered safe?

Another consideration is that if the carboy is filled with water, the pressure at the bottom will be a function of the height of the water. If turning the carboy upside-down mutatis mutandis. Clearly, if that pressure is not exceeded, there should not be a problem.

Thank you very much,

Ben

On Fri, Feb 25, 2022 at 9:07 AM Michael <mabuczynski**At_Symbol_Here**hotmail.com> wrote:

As a reminder-

- We should ALWAYS examine the glassware before we use it before we are about to set up. I have seen where a scratch in a beaker caused it to shatter during an experiment /process.

Mike Buczynski

Principal Owner

PSCR Services LLC.


From: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**Princeton.EDU> on behalf of Ralph Stuart <ralph.stuart**At_Symbol_Here**KEENE.EDU>
Sent: Friday, February 25, 2022 8:40 AM
To: DCHAS-L**At_Symbol_Here**Princeton.EDU <DCHAS-L**At_Symbol_Here**Princeton.EDU>
Subject: Re: [DCHAS-L] Pressurization of 5 gallon glass carboy

My thanks to everyone for sharing their thoughts on my question yesterday. I want to point out that the faculty member asked for my help in assessing this risk rather than just ignoring the various warnings etched into the glass by the manufacturer.

The question arose because the member had detected defects in the existing carboys, which are likely to be 40 years old, and had ordered replacements, which included 6 vague warnings, including the reference to the technical information that we couldn't find on their web site. The suggestion to talk to a company rep is the next step.

It is helpful to be reminded of the energy levels involved in pressurized gases, but that was not news to either of us. I do appreciate having the stories people shared with me about bad experiences they've had with similar set ups.

Thanks to everyone for their assistance with this question.

- Ralph

Ralph Stuart, CIH, CCHO
Environmental Safety Manager
Keene State College
603 358-2859

ralph.stuart**At_Symbol_Here**keene.edu

---
For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org
Follow us on Twitter **At_Symbol_Here**acsdchas

--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas
--- For more information about the DCHAS-L e-mail list, contact the Divisional membership chair at membership**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.