From: Samuella B Sigmann <sigmannsb**At_Symbol_Here**APPSTATE.EDU>
Subject: Re: [DCHAS-L] New science building
Date: October 8, 2012 11:35:28 PM EDT
Reply-To: DCHAS-L <DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU>
Message-ID: <FA001EE30BA70F4D926117C13DAFFFDF20A9E655**At_Symbol_Here**XMAIL-MBX-BT1.AD.UCSD.EDU>


I can second this - we fix 10 to 20 of our locks every semester! 
Sammye

On 10/8/2012 6:14 PM, Kennedy, Sheila wrote:

Nancy,

If you’re putting locks on student drawers/lockers, do not buy cheap ones. We’ve spent a huge amount of time (= money, of course) fixing cheap locks in our ‘new’ building (2005).

 

If you can find a space for students to store lab coats and goggles in/near the labs, they will have fewer days when they forget to bring them.

 

Sheila

_____________

Sheila M. Kennedy, CHO

Safety Coordinator | Teaching Laboratories

Chemistry & Biochemistry |University of California, San Diego

9500 Gilman Dr. | La Jolla, CA  92093-0303

Office: (858) 534-0221 | Fax: (858) 534-7687

s1kennedy**At_Symbol_Here**ucsd.edu | http://www-chem.ucsd.edu

 

From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Cathleen Eldridge
Sent: Monday, October 08, 2012 12:06 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Advice on our new science building

 

This is not one of your questions, but if there’s still time, try to add hallway storage/cubbies for student drinks, snacks or other foodstuff you don’t want in the lab.  Satellite Accumulation Areas for waste chemicals often get left out of the design, along with room for regular recycling containers.  Good luck!

 

Cathleen M. Eldridge

Associate Director

Environmental Health & Safety

SUNY Plattsburgh

101 Broad Street

Plattsburgh, NY  12901

Office: 518-564-5009

Fax: 518-564-5082

 

From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Richardson, Nancy A
Sent: Monday, October 08, 2012 2:35 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: [DCHAS-L] Advice on our new science building

 

We are building a new building that will house health sciences, physics, biology, and chemistry.  It will be mainly a teaching building with classrooms, teaching labs and faculty office areas.  We may have a few small research areas here and there.  We chemists will have the top(fourth) floor for our 6-8 teaching labs, chemical storage, and office area along with one or two small seminar/meeting rooms for around 24 people.  I teach as well as do safety and so I am trying to give the best safety advice in the design as I can, but feel rather inadequate for the task.  I wonder if others have some advice to offer.  As we design the layouts for the rooms, certain particular questions have arisen and I was wondering what others’ experiences have been with some of the following aspects or other aspects that have not surfaced yet:

 

1.      Are ductless hoods a reasonable choice for some/all teaching labs?  I am most concerned with the great variety of materials that the organic labs use.  They tend to do different experiments every time through the course and I think it might be hard to ensure the filters were always adequate.  Also, other teaching labs get used for research(that uses all different materials) from time to time when lab classes are not meeting.  What opinion could any of you offer on ductless hoods?  Are they ultimately cost effective?  Are they maintenance intensive?

2.      In planning teaching labs, there is a question as to whether all the students in a lab need to be under a hood for distillations of various types or working with other materials such as silica.  The introductory chemistry class lab distills mouth wash in one experiment.  Does the ethanol concentration in the air pose any actual risk or the menthol?  Is there some law that says exactly what should be done under a hood?  Could hexane, methylene chloride, and ether be outside of a hood, for example, with enough general room ventilation and how could these be monitored to ensure safe levels in the listed standards for some chemicals?  The appendix in 1910.1450 suggests 2.5 ft person for hood space, but is this done in teaching lab design when one setup is shared by two or maybe four students?  Would hood bonnets be a good alternative for some things?

3.      Are there some chemically resistant AV projectors that could be placed into labs.  We had wanted projectors in labs before, but since other metal(locks, fume hoods, the safety shower) in the labs had become corroded it was thought that projectors would not stand up to chemical exposure? Or with a good ventilation design will this not be an issue? 

4.      What about storing materials in labs?  Now we have a good bit of storage within the teaching labs in our old building because there is no other place for it, but from what I can tell, there are limits on in lab storage of flammables even if there are flammable cabinets.

5.      What is the practice with regard to receiving chemicals and transporting them to upper floors?  I am especially concerned about gas cylinders.

 

Thank you in advance for any opinions and experience anyone has on these topics and with these issues and perhaps other building design issues.

 

Nancy

 


Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.