From: NEAL LANGERMAN <neal**At_Symbol_Here**CHEMICAL-SAFETY.COM>
Subject: Re: [DCHAS-L] Lockout needed when changing gases?
Date: Tue, 9 May 2017 09:01:02 -0700
Reply-To: neal**At_Symbol_Here**CHEMICAL-SAFETY.COM
Message-ID: 009a01d2c8dd$756d2320$60476960$**At_Symbol_Here**chemical-safety.com
In-Reply-To <9aec952174d1420bb255014ec2934384**At_Symbol_Here**ShCo-Exch3.us.shepherd.ad>


Nickie

 

I have never seen LOTO used to change a cylinder.  Unless your system is controlled via a remote activation, the steps in cylinder change result in system isolation.  The cylinder technician has complete control from the time they shut the cylinder valve and delivery valve (on the delivery side of the regulator) until they pressurize the system.  However, work on the system piping, downstream from the regulator, should be covered by LOTO.

 

Neal

 

 

------------------------------------------------------------------------------------

The information contained in this message is privileged and confidential and protected from disclosure. If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify us immediately by replying to the message and deleting it from your computer.

 

ACSafety has a new address:

NEAL LANGERMAN, Ph.D.

ADVANCED CHEMICAL SAFETY, Inc.

PO Box 152329

SAN DIEGO CA 92195

011(619) 990-4908 (phone, 24/7)

www.chemical-safety.com

 

We no longer support FAX.

 

 Please contact me before sending any packages or courier delivery.  The address for those items is:

5340 Caminito Cachorro

San Diego CA 92105

 

 

From: ACS Division of Chemical Health and Safety [mailto:DCHAS-L**At_Symbol_Here**PRINCETON.EDU] On Behalf Of Nickie Norton
Sent: Tuesday, May 9, 2017 4:58 AM
To: DCHAS-L**At_Symbol_Here**PRINCETON.EDU
Subject: Re: [DCHAS-L] Lockout needed when changing gases?

 

I work in R&D for a small manufacturing company and was in a similar situation to yours.  Our R&D group was initially left out of the processes that the plant was involved in, permitting, MOCs, etc.  We now have a Laboratory Chemical Safety Plan that includes the SOPs for what you are describing.  By having the plan in place, we can follow the SOPs.   We only have to do MOCs when permanent renovation changes are involved.  Changing the tubing in our hoods does not require an MOC, but running a permanent vacuum line from a pump to a hood would require an MOC, we would have to have someone from the maintenance department run such a line.  Running a temporary line (such as rubber vacuum tubing from a portable vacuum pump) would not require an MOC.  As for changing gas cylinders, they are covered by an SOP in our Lab Chemical Safety Plan, so no MOC is required.

 

Hope this helps. 

 

Nickie Norton

Research Chemist

The Shepherd Chemical Company

4900 Beech Street

Norwood, OH  45212

nnorton**At_Symbol_Here**shepchem.com

513-842-9332

 

 

Notice: The information disclosed in this communication constitutes confidential and proprietary business information which is the property of The Shepherd Chemical Company.  The information is being disclosed to you and accepted by you on a confidential basis.  It is not to be disclosed by you to any third parties without the prior express written consent of The Shepherd Chemical Company.  Further, it is not to be used by you for any purpose other than for the specific purpose it was disclosed to you by The Shepherd Chemical Company.  These confidentiality and non-use obligations shall continue until such time as the information becomes generally available to the public, through no fault of your own.

 

 

 

From: ACS Division of Chemical Health and Safety [mailto:DCHAS-L**At_Symbol_Here**PRINCETON.EDU] On Behalf Of Corcoran, Hannah
Sent: Monday, May 08, 2017 7:46 PM
To: DCHAS-L**At_Symbol_Here**PRINCETON.EDU
Subject: [DCHAS-L] Lockout needed when changing gases?

 

I am a part of a group that is currently reviewing and updating the company’s safety standards.  The company has mainly focused on the industrial process plant in the past, designating R&D along with all administrative areas as “unclassified”.  This has allowed the lab to conduct research with minimal need for permits, MOCs, and other obstacles that are more pressing at the plant scale (kTon).  It is quite obvious that R&D is more hazardous than an office area and thus should adhere to more stringent standards.  My goal as the R&D representative is to make the laboratory as safe as possible without completely hindering progress. 

 

My question lies within the Line/Vessel Opening safety standard.  The current policy states “a permit is required before any line can be opened or removed.”  At the laboratory scale this doesn’t seem practical.  We build our vacuum/pressure/piping systems ourselves in most cases (using the appropriate glassware or stainless steel for the conditions) and often make modifications based on reaction observations and results.  It is important to note that we do not modify vessels that are rated for pressurized reactions, only the piping that feeds the gas.  Our piping systems are primarily 1/4” or 1/8” SS or copper tubing  which we cut and bend ourselves.  Is it necessary to write a permit for each modification?  Are there certain exceptions I can site when writing this standard?

 

Also, technically changing gas cylinders involves a line opening as well.  We have a lab SOP for this process.  Should a permit be required?

 

I am the CHO for my lab and a researcher, so I’d like to find a compromise that puts safety first without impeding lab work entirely.

 

Does anyone have experience with this type of situation/policy?

 

Hannah Corcoran

R&D Facility Lead

Emerald Kalama Chemical, LLC

1296 Third St NW

Kalama, WA 98625

360-673-0319  (office)

hannah.corcoran**At_Symbol_Here**emeraldmaterials.com

 

"Attitude is a little thing that makes a big difference." – Winston Churchill

 

 

Keeping Life in Your Products.

Visit EmeraldMaterials.com

CONFIDENTIALITY NOTICE:
Both the individual sending this e-mail and Emerald Performance Materials, LLC intend that this electronic message be used exclusively by the individual or entity to which it is intended to be addressed. This message may contain information that is privileged, confidential and thereby exempt and protected from unauthorized disclosure under applicable law. If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering the message to the intended recipient, be aware that any disclosure, dissemination, distribution or copying of this communication, or the use of its contents, is not authorized and is strictly prohibited. If you have received this communication and are not the intended recipient, please notify the sender immediately and permanently delete the original message from your e-mail system.

--- For more information about the DCHAS-L e-mail list, contact the Divisional secretary at secretary**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

--- For more information about the DCHAS-L e-mail list, contact the Divisional secretary at secretary**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.